AEG L 77685 WD Manuel d'utilisateur

L 77685 WD EN User manual

5.4 Start/Pause button 4Press button 4 to start or interrupt aprogramme.5.5 Delay start button 5Press button 5 to delay the start of aprogramme from 3

• To activate the function, press button10 and button 9 at the same timeuntil the display shows the symbol .• To deactivate the function, press but-t

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsFeinwäsche40° - ColdDelicate fabrics asacrylics, viscose, pol-yester items

ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctionsWASHING PROGRAMMESSuper Eco6)ColdMixed fabrics (cottonand synthetic items)

6.1 Programmes for automatic dryingLevel of dryness Type of fabric LoadExtra dryFor towelling materialsCotton and linen(bathrobes, bath towels,etc)up

• The wool wash of this machine hasbeen tested and approved by TheWoolmark Company for the washingof wool containing garments labelledas «hand wash» p

8. BEFORE FIRST USE1.To activate the drain system, put 2 li-tre of water in the main wash com-partment of the detergent dispens-er.2.Put a small quant

The detergent compartment for the prewash phase, the soakprogramme and for the stain function.Add the detergent for prewash, soak and stain remover be

4.To use liquid detergent, turn theflap down.With the flap in the positionDOWN:– Do not use gelatinous or thickliquid detergents.– Do not put more liq

2.Press button 4 , the appliancestarts the countdown of the delaystart.When the countdown is completed,the programme starts automatically.Before you p

CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY

10. USING THE APPLIANCE - DRYING ONLYWARNING!Open the water tap. Put the drainhose in the sink or connect to thedrain pipe.• Load the laundry.• Turn t

11. USING THE APPLIANCE - WASHING & DRYING11.1 NON-STOP programme -Washing & Automatic dryingCAUTION!Do not put a plastic device/ballfor the d

Final time value (washing+ drying + anti-crease +cooling phases)If you set a drying time of only 10minutes, the final time value in-cludes also the an

• A very small load can cause balanceproblems with the spin phase. If thisoccurs, adjust manually the items inthe tub and start the spin phase again.1

– Sleeping bags– Fabrics with residue of hair sprays, nailsolvents or similar.– Garments with foam-rubber or materi-als similar to foam-rubber.12.6 Ga

13.4 Door sealRegularly examine the seal and removeall objects from the inner part.13.5 DrumRegularly examine the drum to preventlimescale and rust pa

13.7 Drain pumpRegularly examine the drainpump and make sure that it isclean.Clean the pump if:• The appliance does not drain the wa-ter.• The drum ca

7.Remove fluff and objects from thepump.8.Make sure that the impeller of thepump can turn. If this does not oc-cur, contact the service centre.129.Cle

4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with astiff brush or a towel.45°20°6.Install again the inlet hose. Makesur

• - The appliance does not drainthe water.• - The appliance door is open ornot closed correctly.• - The anti-flood device is on.WARNING!Deactivate the

1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i

Problem Possible cause Possible solution The filter of the drainpump is blocked.Clean the filter of the drainpump. Refer to 'Care and clean-ing&

Problem Possible cause Possible solutionThe cycle is longerthan the time dis-played.An unbalanced laundryload increases the dura-tion time.This is a n

15. INSTALLATION15.1 Fixing plate kit(4055171146)Available from your authorized dealer.If you install the appliance on a plinth,secure the appliance i

5.Open the door. Remove the poly-styrene piece from the door sealand all the items from the drum.6.Put one of the polystyrene packag-ing elements on t

10.Remove the three bolts. Use the keysupplied with the appliance.11.Pull out the plastic spacers.12.Put the plastic caps in the holes.You can find th

• The appliance must be level and sta-ble.CAUTION!Do not put cardboard, wood orequivalent materials below theappliance feet to adjust the level.Make s

• Connect the water inlet hose to thecold water tap with 3/4 thread.CAUTION!Make sure that there are no leaksfrom the couplings.Do not use an extensio

• On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the water tap orthe wall.• To a

• Directly to a built-in drain pipe in theroom wall and tighten it with a clip.You can extend the drain hose tomaximum 400 cm. Contact theservice cent

ENGLISH 39

• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.

www.aeg.com/shop132918722-A-452013

Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se

• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove the door catch to preventchildren and pets to get cl

4. PRODUCT DESCRIPTION1 2 3 8956741011121Worktop2Detergent dispenser3Control panel4Door handle5Rating plate6Drain pump7Feet for the appliance level8Wa

5. CONTROL PANELKoch/Bunt+ VorwäschePflegeleicht+ VorwäscheLeichtbügelnFeinwäsche20 Min. - 3 kgpotS noN.niM 06tnuB/hcoKthcielegelfP/nreduelhcSnepmuPne

B • The default spin speed of the programme.•'No Spin'1) and 'Rinse Hold' symbols.CDryness levels symbols:2)Iron dryStore dryExtra