LAVAMAT 61470 WDBI EN User manual
• after pressing button 8: it will be im-possible to change any other pro-gramme or option.To enable or disable this option press si-multaneously for
ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsDelicates40° - 30°Max. load kg 3 - Reduced load kg 2Delica
ProgrammeMaximum and Minimum TemperatureType of LaundryMaximum LoadCycle De-scriptionOptionsCotton Economy60°Max. load 7 kgWhite and fast coloured cot
6.1 Drying programmesTimed programmesDegree of Drying Type of FabricDryingLoadSpinSpeedSugges-teddryingtimeMinutesEXTRA DRYIdeal for towelling mate-ri
7. CONSUMPTION VALUESProgramme Energy con-sumption(KWh)Water con-sumption(litres)Programmeduration(minutes)Cottons 60° 1.35 67For the du-ration of the
Make sure that no laundry stays betweenthe seal and the door. There is a risk ofwater leakage or damage to the laundry.9.2 Filling the detergent and a
If you turn the programme dial toanother programme when theappliance is working, the yellowpilot light of button 8 blinks 3times. The display shows th
9.9 Setting the DELAY START(button 9)Press this button again an again to setthe required delay.The display shows the set delay time val-ue (up to 20 h
The water must be emptied out beforeopening the door. During this time thedrum continues to turn at regular inter-vals until water drain.Follow the be
7.Turn the selector dial to the O posi-tion to switch the machine off.8.Remove the laundry.Note!The different type of cottons (towelling,sheets, shirt
CONTENTS1. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32. SAFETY
11. HELPFUL HINTS AND TIPS11.1 The laundry load• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions
Water hardness tableLevel TypeWater hardness°dH °T.H. mmol/l Clarke1 soft 0-7 0-15 0-1.5 0-92 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.
13. CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.13.1 DescalingThe water we use contains limescale. If i
MAX3.Remove the top part of the liquidadditive compartment.4.Clean all the parts with water.5.Clean the dispenser recess with abrush.6.Put back the di
5.When no more water comes out,unscrew the pump cover (A) by turn-ing it anti-clockwise and remove thefilter. Use pliers, if necessary.Always keep a r
To clean the water inlet filters:1.Close the water tap.2.Remove the water inlet hose fromthe water tap.3.Clean the filter in the inlet hose witha stif
By doing this, any water remaining in themachine is removed, avoiding ice form-ing and consequently damage to the ap-pliance.When you use the machine
Problem Possible cause/SolutionThe machine does notfill:The water tap is closed. • Open the water tap.The inlet hose is squashed or kinked. • Check th
Problem Possible cause/SolutionUnsatisfactory washingresults:Too little detergent or unsuitable detergent hasbeen used.• Increase the detergent quanti
Problem Possible cause/SolutionThe machine does notdry or does not dryproperly:The drying time has not been selected.• Select the drying time.The wate
1. SAFETY INFORMATIONBefore the installation and use of the appliance, careful-ly read the supplied instructions. The manufacturer isnot responsible i
15. INSTALLATION15.1 Unpacking1.Use the gloves. Remove the externalfilm. If necessary, use a cutter.2.Remove the cardboard top.3.Remove the polystyren
6.Put one of the polystyrene packag-ing elements on the floor behindthe appliance. Carefully put downthe appliance with the rear side onit. Make sure
12.Put the plastic caps in the holes.You can find these caps in the usermanual bag.WARNING!Remove all the packaging andthe transit bolts before you in
15.3 The inlet hose20O20O20O45O45O45O• Connect the hose to the appliance.Turn the inlet hose only left or right.Loose the ring nut to set it in the co
With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide can-not move when the appliance drains.Attach the guide to the
Without the plastic hose guide.• To a sink spigot.Refer to the illustration. Put the drainhose in the spigot and tighten it with aclip. Make sure that
16. BUILDING IN16.1 Building in600 mm555 mm596 mm170 mm75 mm100 mm60 mmmin.820 mmmin.560 mm818 mm• This appliance has been designed tobe built into th
12• HingesTo mount the hinges it is necessary todrill two holes (dia. 35 mm, depth12.5-14 mm depending on the depthof door furniture) on the inner sid
ABCEDIf the door has to be opened from left toright, invert the position of the plates E ,the magnet D and the plate C. Mountthe counter-magnet D and
ENGLISH 39
• If the supply cord is damaged, it must be replaced bythe manufacturer, its service agent or similarly quali-fied persons in order to avoid a hazard.
www.aeg.com/shop132927181-A-082013
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected tothe water mains using the new sup-plied hose-se
• Disconnect the appliance from themains supply.• Cut off the mains cable and discard it.• Remove the door catch to preventchildren and pets to get cl
4. PRODUCT DESCRIPTION7 8 9101 234561Detergent dispenser2Control panel3Door handle4Rating plate5Drain pump6Feet for the appliance level7Water drain ho
5. CONTROL PANEL1 2 3 4 5 6 7 98 10ABC1Programme selector dial2SPIN button•Rinse hold position 3STAIN button4TIME SAVE button5EXTRA RINSE button6DRYIN
Alarm codesIn the event of operating problems, some alarm codes can bedisplayed, for example (see chapter «Troubleshooting»).End of programmeWhen the
Commentaires sur ces manuels