AEG KVH 32 Guide d'installation

KVH Industries, Inc.Installation GuideTracVision® TV5

9Inside the antenna, a shipping restraint prevents the antenna assembly from moving during shipment. Follow these steps to remove this shipping restra

10Follow these steps to mount the antenna.a. Place the antenna over the holes drilled in the mounting surface. Ensure the forward arrow points toward

11Follow these steps to install the TV-Hub inside the vessel.a. Tape the mounting template in the location selected for the TV-Hub. Punch holes at eac

12Follow these steps to connect the antenna to the TV-Hub. a. Connect the RF1 cable from the antenna to the “Antenna” jack on the TV-Hub (see Figure 1

13The steps for connecting the customer’s receiver(s) to the TracVision system and setting them up depends upon the customer’s satellite TV service (s

14Linear WiringFollow these steps to connect linear receivers to the TracVision system (linear universal quad LNB required). Connecting 1-4 Linear Rec

15Connecting 5 or More Linear Receiversa. Connect an RF cable from the “Receiver” jack on the TV-Hub to the “18V” jack on the multiswitch (see Figure

16DIRECTV – SWM WiringFollow these steps to connect DIRECTV SWM receivers to the TracVision system (circular LNB and TV-Hub A required).NOTE: You can

17Connecting 9-16 SWM Receivers (or Tuners)To connect more than 8 tuners, first follow the steps for 2-8 tuners, as explained on the previous page. Th

18DIRECTV – Non-SWM WiringFollow these steps to connect non-SWM receivers to the TracVision system (circular LNB and TV-Hub A required).NOTE: You can

TracVision TV5 Installation Guide1KVH, TracVision, and the unique light-colored dome with dark contrasting baseplate are registered trademarks of KVH

19DIRECTV Latin America WiringFollow these steps to connect DIRECTV Latin America receivers to the TracVision system (DIRECTV L.A. circular LNB requir

20Tri-Americas WiringFollow these steps to connect both DIRECTV Latin America and DIRECTV U.S. receivers to the TracVision system (see Figure 31) (Tri

21DISH Network and Bell TV WiringFollow these steps to connect DISH Network or Bell TV receivers to the TracVision system (circular LNB required). Con

22At the customer’s option, you can connect a NMEA device to the TV-Hub, allowing the antenna to use its GNSS position and heading data to speed up sa

23Before connecting power, be sure the vessel is properly grounded in accordance with marine standards.Grounding RequirementsProper grounding of the T

24Connect Power to the SystemNOTE: When powering up a SWM configuration, apply power to all other system components before powering up the receivers a

25Follow these steps to turn on the system for the first time.a. Ensure the antenna has a clear, unobstructed view of the sky.b. Press the power switc

26Follow the steps for either option below to access the TV-Hub’s web interface.Using the Wireless Connectiona. Select the TVHub-<TV-Hub serial num

27Connecting the TV-Hub to an onboard local area network (LAN) is required if any of the following conditions apply:• One or more IP AutoSwitches are

28By default, the TV-Hub’s wireless settings are configured for the following:• Wireless Mode: AP (Access Point)• SSID: TV-Hub-<TV-Hub serial numbe

2This icon indicates a danger, warning, or caution notice. Be sure to read these carefully to avoid injury. WARNINGRisk of Electric ShockTo avoid elec

29The Setup Wizard appears upon initial startup to step you through system configuration (see Figure 48). Before you begin to set up the system:• Know

30Setup WizardSystem configuration continues by prompting you to enter information or perform certain tasks, as necessary. For example:• Enter install

31Linear Receiver Setup for Automatic SwitchingFor automatic switching to work properly using the DiSEqC communications protocol, set up linear receiv

32Follow these steps to set the antenna’s LNB to the skew angle supplied by the Setup Wizard.a. At the rear panel of the TV-Hub, set the power switch

33Before you leave the vessel, test the system to ensure the antenna works properly. Fill out the Installation Checklist (provided in the Welcome Kit)

34Follow these steps to add an IP AutoSwitch (KVH part no. 72-0634) to each DISH Network, Bell TV, or linear receiver you want to be able to control s

35Wire the IP AutoSwitchThe wiring of the IP AutoSwitch depends on the specific configuration. Refer to the wiring diagrams provided in “Wire the Rece

36Configure the IP AutoSwitchWhen performing system setup (see “Set Up the System” on page 29), follow these additional steps to configure the IP Auto

37Band/Polarization ControlIf your configuration consists of linear receivers connected via a multiswitch, and you installed one or more IP AutoSwitch

38In Automatic satellite switching mode, the TV-Hub can accept commands from the master SWM-compatible DIRECTV receiver to automatically switch betwee

3Before you begin, follow these steps to ensure you have everything needed to complete the installation.a. Unpack the box and ensure it contains every

39Genie ConfigurationsFull DECA Broadband functionality is built into Genie DVRs (HR44 or HR34). So if a Genie DVR is present on the DIRECTV SWM netwo

40Additional Equipment for Older ReceiversIn addition to the DECA Broadband Kit or a Genie DVR, you might need to connect an additional device in-line

41Configuring the DIRECTV Receivers for Automatic SwitchingTo establish communications between the TracVision system and each SWM-compatible DIRECTV r

42Assigning Static IP Addresses to DIRECTV ReceiversOnce you have identified a valid static IP address range for the receivers, follow these steps to

43i. Add the new receivers to the Autoswitch page of the web interface. Enter each receiver’s static IP address and assign it a friendly name (e.g., “

www.kvh.com KVH Industries, Inc.World HeadquartersMiddletown, RI U.S.A.Tel: +1 401 847 3327 Fax: +1 401 849 0045E-mail: [email protected] KVH Indus

4Before you begin, consider the following antenna installation guidelines.• Minimize blockage. The antenna requires a clear view of the sky to receive

5Consider the following TV-Hub installation guidelines.• Select a mounting location in a dry, well-ventilated area belowdecks away from any heat sourc

6Once you have identified a suitable antenna mounting site, according to the guidelines provided on page 4, follow these steps to drill the mounting h

7Determine the necessary type of RF cable(s) and connectors you need for any RF cables that are required in addition to what is supplied in the antenn

8Follow the steps below to connect the antenna cable(s) to the antenna.a. First determine the number of RF coax cables you need for your installation