L 70260 TLEN WASHING MACHINE USER MANUALDownloaded From WashingMachine-Manual.com Manuals
• To deactivate the function press button5 and button 6 at the same time un-til the indicator of button 7 is off.WASHING PROGRAMMESProgrammeTemperatur
ProgrammeTemperatureType of loadmax. weight of loadCycledescriptionFunctions Spin / Drain4)All fabricsThe maximum load ofthe laundry is relatedto the
4) The default phase of the spin speed is related to cotton items. Set the spin speed. Makesure that it agrees with the laundry. To select the DRAIN p
1) Refer to the display for the programme time.2) The consumption information shown in this chart is indicative. It can vary depending on thequantity
USING THE DETERGENT AND ADDITIVESThe detergent compartment for the prewash phase.The detergent compartment for the washing phase.Liquid additives comp
2.Press button 4 , the appliance startsthe countdown of the delay start.When the countdown is completed,the programme starts automatically.Before you
HELPFUL HINTS AND TIPSTHE LAUNDRY LOAD• Divide the laundry in: white, coloured,synthetics, delicates and wool.• Obey the washing instructions that are
Water hardness tableLevel TypeWater hardness°dH °T.H. mmol/l Clarke1 soft 0-7 0-15 0-1.5 0-92 medium 8-14 16-25 1.6-2.5 10-163 hard 15-21 26-37 2.6-3.
CARE AND CLEANINGWARNING!Disconnect the appliance from the mainssupply before you clean it.DESCALINGThe water we use contains limescale. If itbecomes
1.Open the drain filter door.2.Put a container below the recess ofthe drain filter to collect the waterthat flows out. Turn the filter until it isvert
CONTENTS4 SAFETY INFORMATION6 PRODUCT DESCRIPTION6 ACCESSORIES7 CONTROL PANEL10 WASHING PROGRAMMES13 BEFORE FIRST USE13 USING THE APPLIANCE13 LOADING
4.Remove the inlet hose behind theappliance.5.Clean the filter in the valve with a stiffbrush or a towel.90˚6.Install again the inlet hose. Make suret
TROUBLESHOOTINGThe start of the appliance does not occuror it stops during operation.First try to find a solution to the problem(refer to the table).
Problem Possible cause Possible solutionThe anti-flood de-vice is on. • Disconnect the appliance.• Close the water tap.• Contact the service centre.T
Problem Possible cause Possible solutionThe appliance fillswith water anddrain immediately.The end of the drainhose is too low.Make sure that the drai
INSTALLATIONUNPACKING1.Remove the external film. If necessa-ry, use a cutter.2.Remove the polystyrene packagingmaterials.3.Tilt the appliance backward
8.Remove the power supply cable andthe drain hose from the hose holders.219.Remove the three bolts.11210.Remove the plastic piece.11.Replace the plast
WARNING!Remove all the packaging and thetransit bolts before you install theappliance.We recommend that you keep thepackaging and the transit bolts fo
THE INLET HOSE90˚1.Connect the hose to the appliance.Loose the ring nut to set it in the cor-rect position.2.Connect the water inlet hose to thecold w
With the plastic hose guide. • On the edge of a sink.• Make sure that the plastic guide cannotmove when the appliance drains. At-tach the guide to the
• Directly to a built-in drain pipe in theroom wall and tighten it with a clip.You can extend the drain hose tomaximum 400 cm. Contact theservice cent
FOR PERFECT RESULTSThank you for choosing this AEG product. We have created it to give youimpeccable performance for many years, with innovative techn
30www.aeg.comDownloaded From WashingMachine-Manual.com Manuals
ENGLISH31Downloaded From WashingMachine-Manual.com Manuals
www.aeg.com/shop 108617200-C-092012Downloaded From WashingMachine-Manual.com Manuals
SAFETY INFORMATIONBefore the installation and use, read thismanual carefully:• For your safety and the safety of yourproperty• To help the environmen
• Make sure not to cause damage to thewater hoses.• Do not connect the appliance to newpipes or pipes not used for a long time.Let the water flow for
PRODUCT DESCRIPTION2315469810117121Control panel2Lid3Lid button4Filter access door5Lever to move the appliance6Adjustable feet7Rating plate8Mains cabl
CONTROL PANEL1 2 3456789101On/Off button2Programme knob3Display4Start/Pause button 5Delay start button 6Time saving button 7Extra rinse button 8Stain
The display shows:A • The maximum temperature of the programme.B • The default spin speed of the programme.•'No Spin'1) and 'Rinse Hold
TIME SAVE BUTTON 6Press the button 6 to decrease the pro-gramme duration.• Press one time to set 'Shortened dura-tion' for items with daily
Commentaires sur ces manuels